Product Detail

AUDI A4 (8D2, B5) 1.6 1994-2000

AUDI A4 (8D2, B5) 1.8 1995-2000

AUDI A4 (8D2, B5) 1.8 quattro 1995-2000

AUDI A6 (4B2, C5) 1.8 1997-2005

AUDI A6 Avant (4B5, C5) 1.8 1997-2005

AUDI A4 Avant (8D5, B5) 1.6 1994-2001

AUDI A4 Avant (8D5, B5) 1.8 1995-2001

AUDI A4 Avant (8D5, B5) 1.8 quattro 1995-2001

VW PASSAT Saloon (3B2) 1.6 1996-2000

VW PASSAT Saloon (3B2) 1.8 1996-2000

VW PASSAT Saloon (3B2) 1.8 Syncro/4motion 1996-2000

VW PASSAT Variant (3B5) 1.6 1997-2000

VW PASSAT Variant (3B5) 1.8 1997-2000

VW PASSAT Variant (3B5) 1.8 Syncro/4motion 1997-2000

Description

Fitment: AUDI A4 (8D2, B5) 1.6 1994-2000/AUDI A4 (8D2, B5) 1.8 1995-2000/AUDI A4 (8D2, B5) 1.8 quattro 1995-2000/AUDI A6 (4B2, C5) 1.8 1997-2005/AUDI A6 Avant (4B5, C5) 1.8 1997-2005/AUDI A4 Avant (8D5, B5) 1.6 1994-2001/AUDI A4 Avant (8D5, B5) 1.8 1995-2001 and so on.

OEM Replacement Number: 058133063H/058133063E .Please reference your old Electronic Throttle Body to check it.

Item-condition: Complete Throttle Body Assembly – Includes Throttle Actuator, Idle Air Control and Throttle Position Sensor

Function:Electronic throttle is the throttle pedal and throttle between the traditional cable link, but through electronic sensors to control, control accuracy is higher, to improve the throttle hysteresis phenomenon.frequently requires replacement as internal electronic sensor failure and excessive wear and tear

We are promise Within 1 year if have any damage will send the replacement. if have any question（Such as electric throttle control actuator fails, cracks, stops working or any other problems,）, please contact with us, we will solve it for you. please don’t worry and feel free shopping. thank you.

Some Tips

What’s a throttle body?

The throttle body is a tube containing a pivoting flat valve (butterfly) that is used to control the amount of air entering an engine. In an electronically fuel-injected car, a throttle position sensor and air flow sensor communicate with the computer, which supplies the corresponding amount of fuel needed at the injectors.

How can a throttle body be cleaned?

This is why the butterfly and throttle body need periodic cleaning. After removing it from the intake, clean the throttle body with an aerosol solvent carburetor/fuel injection cleaner and  small brush, or cotton cloth. Pay particular attention to the throttle butterfly, which is attached with small screws (often staked to the throttle pivot to prevent removal) but you don’t need to remove it to clean it.

If the throttle position sensor (TPS) or air flow sensor are on the throttle body, be careful with them. Removal of the TPS may require recalibration afterwards. Mass Air Flow (MAF) sensors are very sensitive to being contaminated, and have a specific solvent spray just for cleaning them.

Some Introduction

When the driver presses on the accelerator pedal, the throttle plate rotates within the throttle body, opening the throttle passage to allow more air into the intake manifold, immediately drawn inside by its vacuum. Usually a mass airflow sensor measures this change and communicates it to the ECU. The ECU then increases the amount of fuel injected by the injectors in order to obtain the required air-fuel ratio. Often a throttle position sensor (TPS) is connected to the shaft of the throttle plate to provide the ECU with information on whether the throttle is in the idle position, wide-open throttle (WOT) position, or somewhere in between these extremes.